 |
|
A, use
1.1 constant wave series ultrasonic washing machine is the production of HB ultrasound single-slot, some small. With water to wash, various additives as ultrasonic cleaning medium, suitable for machinery, metal and glass
Vessels, medical apparatus and instruments, clocks and watches, jewelry and electronic components industry production high quality, high efficiency, and also as a regular cleaning lab cleaning equipment.
Second, ultrasonic cleaning the basic principle and characteristics
Ultrasonic generator generated by 2.1 above 20KHZ super audio signals, through the piezoelectric transducers inverse effect with frequency conversion into mechanical vibration, and with super audio wave forms in cleaning
Radiation. Because of the propagation of logitudinal wave super audio pressure and pressure, produced numerous alternate over 1,000 atmospheres of tiny bubbles and immediately, the formation of the instantaneous blast cleaned surface
Micro partial pressure bombardment, make the surface crack in the dirt quickly and spalling, this is the ultrasonic cleaning peculiar "cavitation effect".
By cleaning medium "2.2 cavitational effect", ultrasonic cleaning has the following features:
1) ultrasonic cleaning area, slit, irregular holes, grooves, fine quality requirements, don't effective surface.
2) cleaning, high efficiency, general cleaning time for several seconds for materials.
3) with water or organic solvent instead of conventional fuel, reducing cost of washing detergent.
Third, the whole structure and characteristics
NC - 1004 1006 type ultrasonic cleaning machine structure as shown
1, chassis
2, the cleaning trough
3, water valve
4 and transducer
5, ultrasonic generator (internal)
6 and the thermostat
Seven, the power indicator
8 and the power switch
9, the heating plate
The cleaning trough, into the fuselage, ultrasonic generator, heating and temperature of five.
NC - 1004 1006 type ultrasonic cleaning machines for stainless steel structure, advanced transistor circuit, all raw materials, electronic components are imported, compact structure, easy to operate.
Four, the main technical parameters
4.1 main technical parameters, see table 1
NC - 1004 NC 1006 -
Ultrasonic power
2million 300W
Inside the tank size
L * W * * * H 250 200 680 mm
L * W * * * H 420 200mm 270
Shape dimension
L x W x H * * 370mm 460 330
L x W x H * * 365mm 626 39
power
Single-phase 220VAC ± 10% 50/60HZ
Ultrasonic frequency
28KHZ or 25KHZ
Fever 500W
Number four sets of six sons shock
15kg 10kg weight
Cleaning the temperature
60 ° c ± 5
Five, the operating instructions
In the cleaning trough infuse 5.1 and clean water to add proper cleaning object properties, wash away the cleaning trough level in the crock 10mm ~ 60mm, actual level range should be cleaned in scope
The strongest effect of ultrasonic resonance obtained a certain level.
Ultrasonic cleaning thermostat and 5.2 will switch power source, for "close" (OFF).
The machine will be the black 5.3 ultrasonic transmission line connected to the source, and ultrasonic knob to tighten.
Ultrasonic cleaning power and 5.4 will be connected to the power source 220V respectively AC ± 10% power.
Adjust the thermostat, 5.5 cleaning will set the thermostat in 60 degrees Celsius, heaters, heating indicator.
After heated to a temperature of 5.6 preset, heating, will be extinguished indicator of ultrasonic source power switch for "open" (ON) position, start after ultrasonic source, then cleaning.
5.7 (hint: if not heated to a temperature of preset cleaning, start the source of ultrasonic cleaning, will affect the workpieces cleaning effect.
Six, cautions
6.1 machine in use process, a fault components for ultrasonic transducer and circuit board. High-q piezoelectric transducers humid, such as dust pollution and conductive exotic, will crash
Born leakage, short-circuit, turn, ceramics piece crack failure. Ultrasound PCB as humid, electric dust pollution, the power supply voltage fluctuations, etc., can appear component circuit damage, pressure
Failure is burned. Therefore, in use process should be noted.
Cleaning trough is prohibited 6.2 start-up heater cleaning circumstances, in order to avoid damage the source and ultrasonic transducer heating plate and.
And a strong impact to prevent abvance of 6.3 vibration, not directly on crock bottom surface of workpiece.
Don't make use of process 6.4 overflow crock, cleaning, lest ban flush water splashed into panel vibration caused by fault circuit, or head.
Don't be in damp 6.5 machine ventilated environment does not use.
6.6 voltage change beyond the machine allows range, should be suspended.
6.7 transducer as damp or pollution caused by leakage circuit, or because it is broken, turn, need to repair the company.
6.8 if found suddenly become very a ultrasonic effect, could be circuit fault, ultrasonic should repair normal before use.
From:http://www.okcsb.cn / Ultrasonic cleaning equipments
 |
 |
 |
 |
 |